samsung laser printer error codes Alberton Montana

Established in 1988, UniVision Computers provides computer and network services to much of Montana. Focusing on the high demands of our business customers, we offer remote or on-site support of your network, VOIP phone systems, website development and hosting, as well as keep your business safe with vulnerability testing. Count on friendly service and experience you can count on. Lenovo, HP, Dell, Microsoft, Ruckus, LightSpeed, Vipre and SonicWall.

Local Area Networks|Desktop Computers|Virtual Private Networks|Wireless Networks|Laptops|Wide Area Networks||Laptop Repair|Computer Hardware Repair|Computer Installation|Business Services|Computer Repair|Desktop Computer Repair|Virus Removal|Set-Up|Computer Cabling

Address 2925 Stockyard Rd Unit A, Missoula, MT 59808
Phone (406) 721-8876
Website Link
Hours

samsung laser printer error codes Alberton, Montana

If you do not have the red dot, then this is probably a defective power supply causing the 50 Service error. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. If it doesn't clear the error you may have one of the problems listed below The HP LaserJet II/IID/III/IIID, Apple LaserWriter II and many other Canon SX engine based printers have A broken tooth on one gear is all it takes.

Also verify the configuration through the menus on the printer. These parts are also available on our parts page. This printer has four lights, Paper Jam, Paper Out, Data, and Online. On the LJII/III series the rubber damper on the clutch release solenoid can degrade and become sticky and gummy.

Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again. On the HP Laserjet 4/4M/4+/4M+, our experience so far has shown the halogen lamp to be responsible for most error 50 problems. This may clear the error - either temporarily or permanently. Scroll through items until "I/O =" appears and use the +/- key to display parallel and the enter key to select.

The outer gear should rotate in one direction only with a spring action which limits it rotation. Or are they? The system returned: (22) Invalid argument The remote host or network may be down. It should not rub off!

This 22 uf 25VDC electrolytic capacitor can leak and cause shorts. If the rollers are glazed or you see cracks, replace the roller or assembly. Replace main motor. Your cache administrator is webmaster.

Remove the card and reseat it, try swapping with a know good card from another printer. If error persists, scanner may need replacement. Bad or dirty cartridge contacts. H2 If the fuser is not warming up properly, this code appears.

Replace main motor IIIP/IIP+/IIP Error 57-1 Incompatible memory can be either top or bottom slot. The replacement parts which are made for Canon by Toshiba, do not have the manufacturing problem. Of course it can happen at any page count. In some cases, cheap cables may not be capable of transmitting the data the scanner needs. 16 This number indicates low toner levels.

A common solution is to tighten the connectors at both the scanner assembly and the DC controller. If that does not work, the sensor must be replaced. 50 If there is a malfunction in the fuser, expect to see a code 50 on the display. Under the various codes will be a list of the possible reasons for this occurrence. You could try replacing this with a 50 mp one.

The HP LaserJet 5P/6P indicates service errors in a similar manner to the 4L/4ML except there are 5 indicator lights. Remember the original HP Laserjet has only 128K of memory available, the LJ+ has only 512K and neither one is really upgradeable. In very rare instances, the laser diode itself will be the cause of failure, usually resulting in an error 51. This should rectify issues.Error: Toner light still onAfter replacement of the toner cartridge you might still find the toner light switched on continually.

by Grif Thomas Forum moderator / April 3, 2013 3:17 AM PDT In reply to: sumsang laser printer scx-4521f LSU IS ERROR Flag Permalink Reply This was helpful (1) Collapse - Our travel guide includes Singapore Travel Guide, Bali Travel Guide, Bali Maps, Jakarta Travel Guide, KL Travel Guide, Malaysia Guide, Johor Guide, Malacca Guide and is widely used by travelers, expats Turn the printer off for 15 minutes to see if the error clears. If this does not work, open the computer's printer folder.

Error 30 PS Error XX - ALL PRINTERS PCL file was sent to the printer while in PostScript mode or the PostScript file contains bad data, or you have experienced and Please refer to our CNET Forums policies for details. All Other Manufacturer's -- Select Manufacturer -- Brother Printer Supplies Canon Printer Supplies Dell Printer Supplies Lexmark Printer Supplies Okidata Printer Supplies Samsung Printer Supplies Xerox Printer Supplies Epson Printer Supplies Sensor Arm Stuck or Broken - check for free movement of the sensor arm.

Load paper and then press and release front panel button. Defective High Voltage power supply or on the LJ II/III the DC controller to High Voltage power supply can be defective. On the LJ4/4M/4+/4M+ the sensor flag can get knocked out of place when a paper jam occurs and the tray is pulled out abruptly. If the paper crinkles right at the toner cartridge it is most likely the drive gear located on the right side of the printer.

On the II and III Series printers, this error message can be caused by a faulty paper control PCA. You can remedy this by replacing the paper guide plate assembly, RG5-248-030. Paper Jam When paper is stuck in or close to the exit rollers, this message appears. You need to check on the fuse located on the front side of the cartridge.

Sometimes you can clean these and get a few more miles out of them but when you start to get jams with a smudge on the top middle of the page, When you have an error, reference the PrinterSupplies.com web site and look on this printer errors page for your number. Balamurugan Flag Permalink Reply This was helpful (0) Collapse - Tip: don't hide new requests in old posts. If you don't allow this capacitor to discharge, you will still get a Error 50 even if you have fixed the problem.

by MarkFlax Forum moderator / February 3, 2012 8:59 PM PST In reply to: error code,(LSU) SAMSUNG LASER PRINTER,SCX-4521F LSU stands for Laser beam Scanning Unit and from what I see This error is usually only reported with the Samsung SCX-4216F device. A switch on this assembly may not be activated properly. Singapore Jobs Streetdirectory.com Streetdirectory.co.id Streetdirectory.com.my © 2016 Streetdirectory

Connect with us facebook twitter CNET Reviews Top Categories CNET 100 Appliances Audio Cameras Cars Desktops Drones Headphones Laptops Networking Phones