socket error # 10054 Premier West Virginia

Address 3130 Cedar Valley Dr, Richlands, VA 24641
Phone (276) 964-2500
Website Link

socket error # 10054 Premier, West Virginia

The application may be accessing a socket that the current active task does not own (that is, trying to share a socket between tasks), or WSACleanup has been called too many Go to Start Menu > Run.Type regedit and press Enter.Navigate to the following folder: HKEY_LOCAL_MACHINE\SOFTWARE\LogMeIn\V5\Net\NATUDPChange the DisableEx (REG_DWORD) key from 0 to 1.Close the Registry Editor.Go to Start Menu > Run.Type services.msc and press And for reconnecting, you'd better create a new socket for it. –Jeroen van Langen Sep 5 '13 at 8:10 @JeroenvanLangen reConnect() method has already create a new socket. See WSAENETUNREACH.

An address incompatible with the requested protocol was used. How come Ferengi starships work? But the short version is that each side is probably waiting for the other. connection http-advanced prtg9 Created on Oct 18, 2011 11:57:26 AM by Daniel Lemos (50) ●1 ●1 Permalink 2 Replies Accepted Answer Votes:1 Your Vote: Up Down 10054 means: An existing connection

Unfortunately, the same error occurs over and over again for a while (a few minutes). WSA_IO_INCOMPLETE 996 Overlapped I/O event object not in signaled state. This message has a slightly different meaning from WSAEAFNOSUPPORT. An MX record is returned but no A record—indicating the host itself exists, but is not directly reachable.

Operations that were in progress fail with WSAENETRESET. Browse other questions tagged c# error-handling tcp-ip or ask your own question. An existing connection was forcibly closed by the remote host. If the problem still persists, contact LogMeIn support.

The call has been canceled. asked 4 years ago viewed 17146 times active 7 months ago Get the weekly newsletter! A QoS error occurred due to lack of resources. WSAVERNOTSUPPORTED 10092 Winsock.dll version out of range.

But my bet is the receive times out and then the connection resets. For example, the ARPA Internet UDP protocol cannot be specified with a socket type of SOCK_STREAM. Dragonflies are among the world’s most efficient predators; they catch 95% of the flying insects that they chase. A reserved policy element was found in the QoS provider-specific buffer.   Requirements Header Winsock2.h; Winerror.h See also Error Codes - errno, h_errno and WSAGetLastError Handling Winsock Errors FormatMessage WSAGetLastError  

Networking activity on the local host has not been initiated. You must make sure that a proper backup of all your data is available. © 1998 - 2016 Paessler AG Solutions • Imprint • Contact • Sitemap • Privacy Policy • WSAENETUNREACH 10051 Network is unreachable. Errors are listed in numerical order with the error macro name.

If this occurs, the user can manually tell the server to connect to the proxy and not directly to the computer. How do I respond to the inevitable curiosity and protect my workplace reputation? I went on the Internet and did a search on this error, and it basically means that the host refused the connection. However, it is interchangeable in most cases, and all Windows Sockets functions that return one of these messages also specify WSAEAFNOSUPPORT.

WSAENETDOWN 10050 Network is down. WSA_QOS_TRAFFIC_CTRL_ERROR 11014 QoS traffic control error. Tell me more detail. Ran out of disk quota.

The call has been canceled. allenJo Post 1 My Internet connection was down some time ago and for the life of me I couldn’t figure out what was causing the problem. WSAENOTEMPTY 10066 Directory not empty. We are trying to understand why the connections get closed for no apparent reason. –Giorgio Jun 12 '12 at 13:12 Have you set a connection timeout? –rekire Jun 12

Before applying any instructions please exercise proper system administrator housekeeping. That they are not trying to use more than one Windows Sockets implementation simultaneously. Sales: 1.800.290.5054 - 1.210.308.8267 Support: 1.210.366.3993 Contact Us Copyright ©1996-2016 GlobalSCAPE, Inc. In some instances, it also refers to the current state of the socket—for instance, calling accept on a socket that is not listening.

The async socket will use IOCP, more on IOCP here:… So it won't hang on your threadpool threads. –Jeroen van Langen Sep 5 '13 at 21:16 Your blog This normally results if the peer application on the remote host is suddenly stopped, the host is rebooted, the host or remote network interface is disabled, or the remote host uses The only thing that is certain is that the problem is not caused directly by VPOP3, since Windows would give a different error code if VPOP3 was closing the connection. A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call.

Windows Sockets Error Codes Most Windows Sockets 2 functions do not return the specific cause of an error when the function returns. Action Check the following items to ensure that your system, firewall and router are configured correctly. The item is not available locally. There are no QoS receivers.

WSA_QOS_EFILTERTYPE 11020 Invalid QoS filter type. Thank you for any ideas and suggestions. This could indicate a serious failure of the network system (that is, the protocol stack that the Windows Sockets DLL runs over), the network interface, or the local network itself. However, when I first tried to do the update, I got a socket error 10061.

There are too many users logged on to the server. The call looks like this: send(socket, (char *) data, (int) data_size, 0); By inspecting the error code we get from WSAGetLastError() we see that it is an error 10054. The service provider procedure call table is invalid. WSANO_RECOVERY 11003 This is a nonrecoverable error.

ProductLogMeIn Rescue; LogMeIn Central; LogMeIn Pro; LogMeIn Hamachi Is this article helpful? DDoS: Why not block originating IP addresses? more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Processes communicate with each other using TCP/IP.

Note that this error is returned by the operating system, so the error number may change in future releases of Windows. The most common cause for a socket error 10054 is the use of an invalid FTP host address. Here is my full source code for communication. An application used a Windows Sockets function that directly maps to a Windows function.

You are invited to get involved by asking and answering questions! WSA_QOS_EPOLICYOBJ 11025 Invalid QoS policy object.